Week 14, May 24, 2019

Today we had to finalize all of our blogs and make sure they were up to date. We did not end up finishing our robot and we also did not complete the remaining challenges.

Week 14, May 20, 2019

This week we plan on finishing our Clawbot. Today we completed our solidworks design. Hopefully this week we will all be here ready to finish the clawbot.

Week 13 May 10, 2019

This week we got literally nothing done. Eduardo was the only one in class today and he was practicing for the solid works certification.

Week 13, May 6, 2019

This week we plan on finishing our solidworks design as well as most of our clawbot. Our design is looking good and we havent run into any problems yet.

Week 12, May 2, 2019

This week we finished most of our solid works design. We have also began to build our claw for our claw bot. We are going to be behind for the Tetrahedron challenge however we plan to complete it with ease.

Week 12, April 30, 2019

This week we plan to finish our solidworks design for our claw bot. We also plan on finishing the actual build for the clawbot, however I have a good feeling we are going to be delayed again. We are gonna try to finish it as fast as possible.

Week 11, April 26, 2019

This week we started building our claw bot. we are still working on our design and are planning as we go to catch up with everyone else. Hopefully we don't run into any complications that could slow us down.

Week 11, April 22, 2019

This week we managed to complete 1 figure 8 autonomously. This means that we are able to get a
50% and move on. Hopefully we do not struggle with the tetrahedron challenge because we are very far behind.

Week 10, April 17, 2019

This week we got almost nothing done. If anything we went backwards. We had to restart our code because it was giving us too many problems. We are very far behind.

Week 10, April 15, 2019

This week our goal is to finish the Figure 8 Challenge and start building our claw bot. We are very far behind and we are struggling, however we can pull through.

Week 9, April 11, 2019

This week was a complete fail. We finally figured out that one of our gears were messed up so we had to replace it. Now we have to recode the entire robot again to fix our mistake.

Week 9, April 9, 2019

This week our goal is to start the tetrahedron challenge. We also need to figure out the problem with our robot before we move on.

Week 8, April 5, 2019

This week we still have not finished our autonomous Figure 8 Challenge yet. Our robot is slowly failing on us so we are working extra hard to fix it.

Week 8, April 1, 2019

this week our goal is to begin the tetrahedron challenge. We are a few steps away from finishing the Figure 8 and we plan on finishing it on Friday.

Week 7, March 20, 2019

This week we finished the figure 8 challenge. Now we have to move onto the tetrahedron challenge

Week 7, March 18, 2019

Today's goal is to get the robot moving in the figure 8 be itself  and continue to improve the robot.

Week 6, March 14, 2019

This week we finally got our robot working without any problems. We have begun to autonomously program our squarebot to run the figure 8. We plan to have it done by next week.

Week 6, March 12, 2019

Our goal for this week is to program our robot to run the figure 8 autonomously. We also have another challenge that needs to get done however we are behind and need to catch up.

Week 5, March 8, 2019

This week we changed our motors as well as our gears. However there is still a problem with them. We were not able to complete or even attempt the figure 8 this week, so that is our number 1 priority next week.

Week 5, March 4, 2019

Our goal this week is to finish testing our robot and make sure everything is functioning. We also need to program our robot to run the figure 8.

Week 4, February 28, 2019

This week we practically finished our robot. We had to get use an alternative battery clip because the 3D Printer was not working.The only thing left to do is to fix our axels and begin testing our robot.

Week 4, February 26, 2019

This week our goal is to finish programming our robot. We also have to swap out all of our broken parts as well as 3D Print our battery clip. We finished all our goals from last week.

Week 3, February 22, 2019

This week we got most of the base of the robot finished. We re almost finished with the solid works drawing and we have fixed our blog with the correct dates and entries. Next week we re going to have to work extra hard to finish the leftover tasks.